Scroll down - 1 line per wheel-notch...
Scroll up - 93 lines per wheel-notch...
Happen to anybody else? Work-around?
I'm using Logitech cordless Laser Mouse with SetPoint 2.40.855 on WinXP pro.
By-the-by - been using this terrific program for years an am a huge fan!
Asymmetric wheel mouse scroll....
-
- New Member
- Posts: 4
- Joined: Mon Sep 19, 2005 11:51 am
There was one problem like yours reported in version 3.2c, and no remedy was found. Here what our reply was:
- Is EDPro the only program that exhibits this problem?
- Does it happen always?
- Does it happen in all EDPro views (text, binary, directories)?
Some questions:We checked the source code, and there appears to be no asymmetry in up vs. down scrolling. In fact, we use MFC (if you are familiar with C++ programming for Windows) code for mouse wheel support, meaning that there's no custom code in ExamDiff Pro that could cause your problem.
- Is EDPro the only program that exhibits this problem?
- Does it happen always?
- Does it happen in all EDPro views (text, binary, directories)?
psguru
PrestoSoft
PrestoSoft
-
- New Member
- Posts: 4
- Joined: Mon Sep 19, 2005 11:51 am
The only one I've noticed, and I use a lot of programs...psguru wrote:- Is EDPro the only program that exhibits this problem?
Yespsguru wrote:- Does it happen always?
Does not do it in Directory compare. I don't use binary compare.psguru wrote:- Does it happen in all EDPro views (text, binary, directories)?
I'll try it without the Logitech mouse/keyboard, and see what happens.
-
- New Member
- Posts: 4
- Joined: Mon Sep 19, 2005 11:51 am
Fixed, but not sure why...
Well... I uninstalled Logitech S/W, keyboard and mouse.
Installed standard keyboard and MS wheel mouse, and Intellipoint 5.2. Still had asymmetric mouse wheel scroll.
Reinstalled Logitech... and still asymmetric scroll.
Fooled around with Logitech's mouse settings, selected (enabled) "Smart Move" on "My Mouse/Mouse Movement" tabs of SetPoint hardware and now the mouse wheel scroll works.
Go Figure... Thanks for the help. Keep up the good work.
Installed standard keyboard and MS wheel mouse, and Intellipoint 5.2. Still had asymmetric mouse wheel scroll.
Reinstalled Logitech... and still asymmetric scroll.
Fooled around with Logitech's mouse settings, selected (enabled) "Smart Move" on "My Mouse/Mouse Movement" tabs of SetPoint hardware and now the mouse wheel scroll works.
Go Figure... Thanks for the help. Keep up the good work.
Interesting. Searching the Web, it would appear as though this setting would cause problems, not fix them...
(See Text selection in Code view is inaccurate in Dreamweaver MX at http://www.macromedia.com/cfusion/knowl ... d=tn_16431 )
(See Text selection in Code view is inaccurate in Dreamweaver MX at http://www.macromedia.com/cfusion/knowl ... d=tn_16431 )
psguru
PrestoSoft
PrestoSoft
-
- New Member
- Posts: 4
- Joined: Mon Sep 19, 2005 11:51 am
Even more interesting...
After that previous "fix", it shortly started doing it again.
This time I selected "restore defaults" in the SetPoint software, reset the few non-default setting I use, and now it works as it should.
Go figure...
In any case, now it works, and I can finish this big job.
This time I selected "restore defaults" in the SetPoint software, reset the few non-default setting I use, and now it works as it should.
Go figure...
In any case, now it works, and I can finish this big job.
I found that my scroll wheel has perhaps a similar effect if the "Current Difference" drop-down is highlighted. Like other drop-downs in Windows if you turn the wheel the next/prev item is selected. If difference #1 is currently displayed and the "Current Difference" control is highlighted, rotating the scroll wheel down one click will move the display to the next difference. Rotate the wheel up one click will move to the previous difference. This is the same behavior if you use the up-down arrow keys.
Perhaps you are finding that when you first start comparing two files this "Current Difference" control right under the buttons is selected. If you want to avoid this behavior make sure to click off of this control.
I like this feature if I am moving from change to change quickly without taking my hand off the mouse. It is also handy just to use the cursor keys.
I hope this helps someone.
Perhaps you are finding that when you first start comparing two files this "Current Difference" control right under the buttons is selected. If you want to avoid this behavior make sure to click off of this control.
I like this feature if I am moving from change to change quickly without taking my hand off the mouse. It is also handy just to use the cursor keys.
I hope this helps someone.